Managing Multiple Hard Drives with cPanel
If you have a server with single standalone drives, you may have considered the possibility of adding additional hard drives to provide more disk capacity to your system. Luckily, this is very easy to set up and use with cPanel.
First things first, I’ll assume that you already have the hard drive physically installed in your system. This guide will show you how to partition, format, and configure cPanel to use an additional hard drive, in the simplest way possible.
1. Partitioning the DiskWe’ll assume that the additional disk is supplementary to a system that already has an existing drive and OS installation. Therefore, the new disk will usually only need to be one single partition, unless you have different planned uses for it. If this is the second disk in your server, it’s going to be named either /dev/sdb or /dev/hdb, depending on what kind of drive it is. The last letter in the drive name will depend on how many other disks you have in your server, so see
訪客無法瀏覽此圖片或連結，請先 註冊 或 登入會員 。 for a simple explanation on Linux drive mappings.
To find the new disk you added, use
fdisk -l, which will list the disks active on your server. The additional disk should show up in the order that it’s physically configured inside the server:
Disk
/dev/sdb: 250.0 GB, 250000000000 bytes
255 heads, 63 sectors/track, 30394 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
If you notice, the already-partitioned volumes also list the partition info. For example, this is what the output for the primary hard drive in my test server looks like, which is already set up with two partitions on the primary drive:
Device Boot Start End Blocks Id System
/dev/sda1 * 1 29884 240043198+ 83 Linux
/dev/sda2 29885 30394 4096575 82 Linux swap / Solaris
The partition information is blank for the new disk, indicating that it has not been partitioned yet. If yours has already been partitioned and you want to keep that structure, you can skip this section and go straight to formatting.
From here, I want to create one partition which will be /home2 on this server, to provide additional capacity for users on this system. GNU parted is a simple command line utility to manage disk partitions, and I’ll use this to create a partition on my new hard drive:
parted /dev/sdb
Once in parted, type
print free to show how much space is available to be partitioned:
Number Start End Size Type File system Flags 0.00kB 250GB 250GB Free SpaceSince I’m only creating one partition, I use the parted
mkpart command to specify the start and end space to occupy the whole disk:
(parted) mkpart
Partition type? primary/extended?
primary
File system type? [ext2]?
ext3
Start?
0kB
End?
250GB
Then when I type in print, I see my new partition listed:
Number Start End Size Type File system Flags
1 0.51kB 250GB 250GB primary
Now, if you’re creating multiple partitions on the disk, do the same thing, but modify the start and end parameters to sequentially create your partitions. In the above example, that partition would have a device name as
/dev/sdb1, since it’s the partition numbered 1 on disk /dev/sdb. If I had a second and third partition, they would be named /dev/sdb2 and /dev/sdb3, respectively.
Type
quit to close the parted session.
2. Formatting and Configuring the DiskOnce you’ve created the partitions, you can format them easily with mkfs.ext[2|3], using the device name as the argument:
- For ext3: mkfs.ext3 /dev/sdb1
- For ext2: mkfs.ext2 /dev/sdb1
- For ext4: 訪客無法瀏覽此圖片或連結，請先 註冊 或 登入會員 。 or the 訪客無法瀏覽此圖片或連結，請先 註冊 或 登入會員 。
Repeat this for all the partitions you created, which will be numbered started as /dev/<device><partition>. My example is using the first partition of the second SCSI hard drive, so the partition device name is /dev/sdb1 . You can also find the new partition names by running
fdisk -l again to see the names of the partitions for the new disk.
I also prefer to set the reserved disk space for the root user, as by default this will be 5% of the total partition size. This means for my 250GB disk, about 12GB is being reserved, which is a bit excessive. I instead usually set this to 2500 blocks:
root@server [~]# tune2fs -r 2500 /dev/sdb1
tune2fs 1.39 (29-May-2006)
Setting reserved blocks count to 2500
TIP: You can also pass
-m <%> to the mkfs.ext[2|3] commands to set the percentage for reserved disk space during formatting, which can of course be changed later with tune2fs
3. Labeling and Mounting the DiskNow, you need to label the disk and add it to fstab. In my example, I want to label the disk as /home2, so I’d use the
e2label command and pass the partition’s device name and my desired label as arguments:
e2label /dev/sdb1 /home2
This can be confirmed by typing e2label /dev/sdb1:
root@server [~]# e2label /dev/sdb1
/home2
In order to mount the partition, it needs a mount point, and to be added to the file system table. Since the partition will be mounted as /home2, I created a folder called /home2, and added the following to /etc/fstab:
LABEL=/home2 /home2 ext3 defaults,usrquota,noatime 0 0
The LABEL value would be set to the label you used in e2label. To find out more about the fstab file, see
訪客無法瀏覽此圖片或連結，請先 註冊 或 登入會員 。. Again, you need to repeat these steps for each partition you created.
After you do this, you can mount the new partitions normally:
mount /home2
4. Setting up cPanelAs far as setting up cPanel, there’s only one file you have to edit – /etc/wwwacct.conf.
- HOMEDIR : The location where all new user home folders will be created (/home by default)
- HOMEMATCH: Additional home directories that will also be used for new home directory creations – only takes one value, leaving blank disables.
So, if you want to specify the partition/folder that all users are set up on, edit the HOMEDIR value and leave HOMEMATCH blank. If you specify a value for HOMEMATCH, cPanel will pick the partition based on which one has the most free space available.
For example, if you specify “home” for HOMEMATCH, it will configure users in the following locations:
- /home
- /home* (/home2, /home3, etc)
- /anythingwith/home
- /usr/home
Additional Resources:
訪客無法瀏覽此圖片或連結，請先 註冊 或 登入會員 。
訪客無法瀏覽此圖片或連結，請先 註冊 或 登入會員 。
